Important Information
Warranty
The VXI-USB is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by
receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the
warranty period. This warranty includes parts and labor.
The media on which you receive National Instruments software are warranted not to fail to execute programming instructions, due to defects
in materials and workmanship, for a period of 90 days from date of shipment, as evidenced by receipts or other documentation. National
Instruments will, at its option, repair or replace software media that do not execute programming instructions if National Instruments receives
notice of such defects during the warranty period. National Instruments does not warrant that the operation of the software shall be
uninterrupted or error free.
A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the outside of the package before
any equipment will be accepted for warranty work. National Instruments will pay the shipping costs of returning to the owner parts which are
covered by warranty.
National Instruments believes that the information in this document is accurate. The document has been carefully reviewed for technical
accuracy. In the event that technical or typographical errors exist, National Instruments reserves the right to make changes to subsequent
editions of this document without prior notice to holders of this edition. The reader should consult National Instruments if errors are suspected.
In no event shall National Instruments be liable for any damages arising out of or related to this document or the information contained in it.
EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CUSTOMER’S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF
NATIONAL INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE LIABLE FOR
DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF. This limitation of the liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including
negligence. Any action against National Instruments must be brought within one year after the cause of action accrues. National Instruments
shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided herein does not cover
damages, defects, malfunctions, or service failures caused by owner’s failure to follow the National Instruments installation, operation, or
maintenance instructions; owner’s modification of the product; owner’s abuse, misuse, or negligent acts; and power failure or surges, fire,
flood, accident, actions of third parties, or other events outside reasonable control.
Copyright
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying,
recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National
Instruments Corporation.
Trademarks
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section
on ni.com/legalfor more information about National Instruments trademarks.
Other product and company names mentioned herein are trademarks or trade names of their respective companies.
Members of the National Instruments Alliance Partner Program are business entities independent from National Instruments and have no
agency, partnership, or joint-venture relationship with National Instruments.
Patents
For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txtfile
on your CD, or ni.com/patents.
WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS
(1) NATIONAL INSTRUMENTS PRODUCTS ARE NOT DESIGNED WITH COMPONENTS AND TESTING FOR A LEVEL OF
RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS CRITICAL COMPONENTS IN
ANY LIFE SUPPORT SYSTEMS WHOSE FAILURE TO PERFORM CAN REASONABLY BE EXPECTED TO CAUSE SIGNIFICANT
INJURY TO A HUMAN.
(2) IN ANY APPLICATION, INCLUDING THE ABOVE, RELIABILITY OF OPERATION OF THE SOFTWARE PRODUCTS CAN BE
IMPAIRED BY ADVERSE FACTORS, INCLUDING BUT NOT LIMITED TO FLUCTUATIONS IN ELECTRICAL POWER SUPPLY,
COMPUTER HARDWARE MALFUNCTIONS, COMPUTER OPERATING SYSTEM SOFTWARE FITNESS, FITNESS OF COMPILERS
AND DEVELOPMENT SOFTWARE USED TO DEVELOP AN APPLICATION, INSTALLATION ERRORS, SOFTWARE AND
HARDWARE COMPATIBILITY PROBLEMS, MALFUNCTIONS OR FAILURES OF ELECTRONIC MONITORING OR CONTROL
DEVICES, TRANSIENT FAILURES OF ELECTRONIC SYSTEMS (HARDWARE AND/OR SOFTWARE), UNANTICIPATED USES OR
MISUSES, OR ERRORS ON THE PART OF THE USER OR APPLICATIONS DESIGNER (ADVERSE FACTORS SUCH AS THESE ARE
HEREAFTER COLLECTIVELY TERMED “SYSTEM FAILURES”). ANY APPLICATION WHERE A SYSTEM FAILURE WOULD
CREATE A RISK OF HARM TO PROPERTY OR PERSONS (INCLUDING THE RISK OF BODILY INJURY AND DEATH) SHOULD
NOT BE RELIANT SOLELY UPON ONE FORM OF ELECTRONIC SYSTEM DUE TO THE RISK OF SYSTEM FAILURE. TO AVOID
DAMAGE, INJURY, OR DEATH, THE USER OR APPLICATION DESIGNER MUST TAKE REASONABLY PRUDENT STEPS TO
PROTECT AGAINST SYSTEM FAILURES, INCLUDING BUT NOT LIMITED TO BACK-UP OR SHUT DOWN MECHANISMS.
BECAUSE EACH END-USER SYSTEM IS CUSTOMIZED AND DIFFERS FROM NATIONAL INSTRUMENTS' TESTING
PLATFORMS AND BECAUSE A USER OR APPLICATION DESIGNER MAY USE NATIONAL INSTRUMENTS PRODUCTS IN
COMBINATION WITH OTHER PRODUCTS IN A MANNER NOT EVALUATED OR CONTEMPLATED BY NATIONAL
INSTRUMENTS, THE USER OR APPLICATION DESIGNER IS ULTIMATELY RESPONSIBLE FOR VERIFYING AND VALIDATING
THE SUITABILITY OF NATIONAL INSTRUMENTS PRODUCTS WHENEVER NATIONAL INSTRUMENTS PRODUCTS ARE
INCORPORATED IN A SYSTEM OR APPLICATION, INCLUDING, WITHOUT LIMITATION, THE APPROPRIATE DESIGN,
PROCESS AND SAFETY LEVEL OF SUCH SYSTEM OR APPLICATION.
Compliance
Compliance with FCC/Canada Radio Frequency Interference
Regulations
Determining FCC Class
The Federal Communications Commission (FCC) has rules to protect wireless communications from interference. The FCC
places digital electronics into two classes. These classes are known as Class A (for use in industrial-commercial locations only)
or Class B (for use in residential or commercial locations). All National Instruments (NI) products are FCC Class A products.
Depending on where it is operated, this Class A product could be subject to restrictions in the FCC rules. (In Canada, the
Department of Communications (DOC), of Industry Canada, regulates wireless interference in much the same way.) Digital
electronics emit weak signals during normal operation that can affect radio, television, or other wireless products.
All Class A products display a simple warning statement of one paragraph in length regarding interference and undesired
operation. The FCC rules have restrictions regarding the locations where FCC Class A products can be operated.
FCC/DOC Warnings
This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the instructions
in this manual and the CE marking Declaration of Conformity*, may cause interference to radio and television reception.
Classification requirements are the same for the Federal Communications Commission (FCC) and the Canadian Department
of Communications (DOC).
Changes or modifications not expressly approved by NI could void the user’s authority to operate the equipment under the
FCC Rules.
Class A
Federal Communications Commission
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference
at their own expense.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Compliance with EU Directives
Users in the European Union (EU) should refer to the Declaration of Conformity (DoC) for information* pertaining to the
CE marking. Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance
information. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line,
and click the appropriate link in the Certification column.
*
The CE marking Declaration of Conformity contains important supplementary information and instructions for the user or
installer.
About This Manual
Chapter 1
VXI-USB Interface Kit Overview .................................................................................1-2
VXI 3.0 Specification Support.......................................................................................1-2
Hardware Description....................................................................................................1-2
VXI-USB Front Panel Features .....................................................................................1-3
Chapter 2
Installing the Software...................................................................................................2-1
Completing the Software Installation..............................................................2-2
Configuring the Hardware (Optional)............................................................................2-3
Installing Your VXI-USB Interface Module...................................................2-5
Chapter 3
Configuration.................................................................................................................3-2
Programming for VXI....................................................................................................3-5
Optimizing Large VXIbus Transfers...............................................................3-7
NI-VXI API Notes...........................................................................................3-8
Compiler Symbols.............................................................................3-8
Compatibility Layer Options ............................................................3-8
Debugging......................................................................................................................3-9
© National Instruments Corporation
v
VXI-USB User Manual
Contents
Appendix A
Specifications
Appendix B
Default Settings
Appendix C
Advanced Hardware Configuration Settings
Appendix D
Technical Support and Professional Services
Glossary
Index
VXI-USB User Manual
vi
ni.com
About This Manual
This manual contains instructions for installing and configuring the
VXI-USB interface kit. It also discusses how to start developing your
VXI/VME application.
Conventions
The following conventions appear in this manual:
»
The » symbol leads you through nested menu items and dialog box options
to a final action. The sequence File»Page Setup»Options directs you to
pull down the File menu, select the Page Setup item, and select Options
from the last dialog box.
This icon denotes a note, which alerts you to important information.
This icon denotes a caution, which advises you of precautions to take to
avoid injury, data loss, or a system crash. When this symbol is marked on a
product, refer to the Safety section in Appendix A, Specifications, for
information about precautions to take.
bold
Bold text denotes items that you must select or click in the software, such
as menu items and dialog box options. Bold text also denotes parameter
names.
italic
Italic text denotes variables, emphasis, a cross reference, or an introduction
to a key concept. This font also denotes text that is a placeholder for a word
or value that you must supply.
monospace
Text in this font denotes text or characters that you should enter from the
keyboard, sections of code, programming examples, and syntax examples.
This font is also used for the proper names of disk drives, paths, directories,
programs, subprograms, subroutines, device names, functions, operations,
variables, filenames, and extensions.
monospace italic
Italic text in this font denotes text that is a placeholder for a word or value
that you must supply.
© National Instruments Corporation
vii
VXI-USB User Manual
About This Manual
Related Documentation
The following documents contain information that you might find helpful
as you read this manual:
•
ANSI/IEEE Standard 1014-1987, IEEE Standard for a Versatile
Backplane Bus: VMEbus
•
ANSI/IEEE Standard 1155-1998, IEEE VMEbus Extensions for
Instrumentation: VXIbus
•
•
•
ANSI/VITA 1-1994, VME64
Universal Serial Bus Specification, Revision 2.0
VXI-6, VXIbus Mainframe Extender Specification, Rev. 2.0, VXIbus
Consortium
•
•
•
NI-VISA Help
NI-VXI Help
Measurement & Automation Explorer Help for NI-VISA/NI-VXI
VXI-USB User Manual
viii
ni.com
1
Introduction
This chapter describes your VXI-USB interface kit, lists what you need to
get started, and includes a brief description of the hardware and software.
The VXI-USB interface kit links a PC-based computer to the VXIbus using
the Universal Serial Bus (USB). This kit makes your computer perform as
if it were plugged directly into the VXI backplane, giving your external
computer the capability of an embedded computer. USB 2.0 features hot
plug-in capability under Windows, which means you can add and configure
USB devices without powering down your system. Your kit contains a
National Instruments VXI-USB interface module, which plugs into your
VXI mainframe and links your computer to the VXIbus. Your kit includes
the NI-VXI/NI-VISA bus interface software, which is fully VXIplug&play
compliant. NI-VXI/NI-VISA is the National Instruments implementation
of the VISA I/O software standard on which all VXIplug&play software
components are based.
What You Need to Get Started
To set up and use the VXI-USB interface kit, you need the following items:
❑ Computer running the Windows 2000 or Windows XP operating
system, with a USB 2.0 port or plug-in card (USB 2.0 plug-in cards
may not have the same level of performance as an integrated USB 2.0
port)
❑ VXIbus mainframe
❑ VXI-USB interface module that plugs directly into a VXI mainframe
❑ USB 2.0-compliant cable
❑ National Instruments software CD
❑ This manual
© National Instruments Corporation
1-1
VXI-USB User Manual
Chapter 1
Introduction
VXI-USB Interface Kit Overview
The interface kit described in this manual links a USB-equipped computer
directly to the VXIbus using USB 2.0. The VXI-USB kit uses this
high-speed (480 Mbps) serial bus to link your computer running Windows
to a VXI chassis.
Note You can use the VXI-USB kit with USB 1.0, but performance will be significantly
slower than with USB 2.0 for many types of operations.
Note You can connect multiple USB devices to the host. However, increasing the number
of USB devices in a system can lower the VXI-USB performance.
The VXI-USB kit includes the NI-VXI/NI-VISA software for Windows,
a C-size VXI-USB module, and a USB cable. A USB-equipped computer
connected to a VXI-USB interface can function as a VXI Commander and
Resource Manager. With the VXI-USB interface kit, your computer
performs as if it is plugged directly into the VXI backplane as an embedded
CPU module. The VXI-USB transparently translates between USB and
VXI protocols.
VXI 3.0 Specification Support
The VXI-USB has been designed for VXIbus Specification 3.0, and also is
compatible with VXIbus Specification 2.0. The VXI-USB supports new
VXIbus 3.0 features such as 2eVME transfers (with a theoretical
bandwidth up to 160 Mbytes/s), A64 memory space allocation, and a
Resource Manager that supports A64 allocation. NI-VXI includes an
NI-VISA driver for the VXI-USB that has additional functionality for using
these VXIbus 3.0 features. If you have a VXI device that supports these
features, consult the VXI-USB release notes for information about how to
access them from NI-VISA.
Hardware Description
The VXI-USB module is a VXIbus Slot 0-capable device, so it can reside
in slot 0 of any C-size or D-size chassis.
however, does not have this connector and cannot provide the necessary control for VXI
devices that need P3 support.
VXI-USB User Manual
1-2
ni.com
Chapter 1
Introduction
The VXI-USB links the computer to the VXIbus and converts USB data
transfers into VXIbus data transfers and vice versa. The VXI-USB includes
additional USB Series A ports you can use to connect other USB devices.
VXI-USB Front Panel Features
The VXI-USB has the following front panel features:
•
Front panel LEDs
–
FAILED—Indicates the VXI-USB is asserting SYSFAIL on the
bus due to a controller failure.
–
SYSFAIL—Indicates the VMEbus SYSFAIL line is asserted by
the VXI-USB or another device on the bus.
–
–
VXI—Indicates the VXI-USB is being accessed as a VXI slave.
ONLINE
•
•
Green—Indicates the VXI-USB is configured by Resman.
Amber—Indicates the VXI-USB is not configured by
Resman.
–
–
USB—Indicates there is USB traffic to/from the VXI-USB (this
excludes any traffic to all other downstream USB devices).
LINK
•
Green—Indicates the VXI-USB is connected to a USB host
and has a full-speed (USB 1.x, 12 Mbps) connection.
•
Amber—Indicates the VXI-USB is connected to a USB host
and has a high-speed (USB 2.0, 480 Mbps) connection.
•
•
•
One host (Series B) USB connector
Two device (Series A) USB connectors
Three SMB connectors
–
–
–
Trigger input
Trigger output
External clock
•
System reset pushbutton
© National Instruments Corporation
1-3
VXI-USB User Manual
Chapter 1
Introduction
Advanced Configuration Options
The VXI-USB default hardware configuration should be acceptable for
most systems. Refer to Appendix B, Default Settings, only if your system
uses the front-panel CLK10 and trigger SMB connectors.
The NI-VISA/NI-VXI bus interface software includes a Resource
Manager, an interactive configuration and troubleshooting program,
a comprehensive library of software routines for VXI/VME programming,
a logging utility you can use for debugging, and graphical interactive
control programs for interacting with VISA. You can use this software to
seamlessly program multiple-mainframe configurations and have software
compatibility across a variety of controller platforms.
NI-VISA has a comprehensive library of software routines not only for
VXI/VME programming, but also for GPIB, GPIB-VXI, PXI, TCP/IP, and
Serial. You can use this software to program instruments connected through
different types of interfaces.
Measurement & Automation Explorer (MAX) helps you view your
entire test and measurement system and configure various components,
whether they are VXI, GPIB, PXI, or Serial devices. You can also add
VME devices to your system easily with MAX and view them on a screen
display along with the rest of your system. MAX also features various
options for running the Resource Manager, Resman. You can still execute
Resman independently to configure your instruments after a power cycle.
But you can also perform resource manager operations directly from MAX
or configure it to run Resman automatically at startup.
The NI Spy utility tracks the calls your application makes to National
Instruments drivers, including NI-VXI, NI-VISA, and NI-488.2. NI Spy
helps you debug your application by clearly highlighting the functions that
return errors. You can let NI Spy keep a log of your program’s calls to these
drivers so that you can check them for errors at your convenience.
National Instruments Application Software
In addition to the NI-VISA/NI-VXI software, you can use the National
Instruments LabVIEW, Measurement Studio, and LabWindows™/CVI™
application programs and instrument drivers to ease your programming
task. These standardized programs match the modular virtual instrument
capability of VXI and can reduce your VXI/VME software development
time. These programs are fully VXIplug&play compliant and feature
VXI-USB User Manual
1-4
ni.com
Chapter 1
Introduction
extensive libraries of VXI instrument drivers written to take full advantage
of direct VXI control. LabVIEW, Measurement Studio, and
LabWindows/CVI include all the tools needed for instrument control, data
acquisition, analysis, and presentation.
LabVIEW is an easy-to-use, graphical programming environment you can
use to acquire data from thousands of different instruments, including
IEEE 488.2 devices, VXI devices, serial devices, PLCs, and plug-in data
acquisition boards. After you have acquired raw data, you can convert it
into meaningful results using the powerful data analysis routines in
LabVIEW. LabVIEW also comes with hundreds of instrument drivers,
which dramatically reduce software development time, because you do not
need to spend time programming the low-level control of each instrument.
Measurement Studio allows you to choose from standard environments
such as Microsoft Visual Basic, Visual C++, and Visual Studio .NET to
create your application, using tools specific for each language. With
Measurement Studio, you can write programs quickly and easily and
modify them as your needs change.
LabWindows/CVI is an interactive ANSI C programming environment
designed for building virtual instrument applications. LabWindows/CVI
delivers a drag-and-drop editor for building user interfaces, a complete
ANSI C environment for building your test program logic, and a collection
of automated code generation tools, as well as utilities for building
automated test systems, monitoring applications, or laboratory
experiments.
To use any of these application programs, install them before installing the
NI-VISA/NI-VXI software. LabVIEW, Measurement Studio, and
LabWindows/CVI integrate the VXI and VISA libraries required to support
your VXI-USB. You also get hundreds of complete instrument drivers,
which are modular, source-code programs that handle the communication
with your instrument to speed your application development.
© National Instruments Corporation
1-5
VXI-USB User Manual
2
Installation and Configuration
This chapter explains how to set up your test system.
Installing the Software
Use the Setup program that came with your NI-VXI/NI-VISA software to
install the entire software package or a software update, or to reinstall
software in the event that your files were accidentally erased. Some of the
utilities rely on the LabWindows/CVI Run-Time Engine. This software is
installed, if necessary, during the NI-VXI/NI-VISA installation.
Depending on the type of installation you choose, you may need up to
50 MB of free space on your hard drive to accommodate the NI-VXI and
NI-VISA software.
To be compliant with VXIplug&play specifications, a VXI controller must
provide the VISA I/O driver library standardized by VXIplug&play. VISA
ensures that your controller can run all VXIplug&play-compatible software
now and in the future.
The NI-VISA software in this kit is compatible with the WINNT/GWINNT
framework. With NI-VISA installed on your computer, you can run any
VXIplug&play software that is compatible with this framework. This
includes instrument drivers and executable soft front panel software
included with VXIplug&play-compatible instruments from a variety of
vendors.
Installing the NI-VXI and NI-VISA Software
This section describes how to install the NI-VXI and NI-VISA software.
Carefully read these directions along with any messages on the screen
before making your selections. You can quit the Setup program at any time
by clicking the Cancel button.
© National Instruments Corporation
2-1
VXI-USB User Manual
Chapter 2
Installation and Configuration
Caution To keep the manufacturer/model name tables or the VME device configuration
from a previous installation, be sure to back them up before starting Setup. They are in the
TBLsubdirectory of your NI-VXI directory, usually Program Files\National
Instruments\VXI.
Setup is an interactive, self-guiding program that installs the NI-VXI and
NI-VISA software and configures your system to use the software with the
VXI-USB. Complete the following steps to perform the installation:
1. For the CD, select Start»Run and enter the following text, where Xis
your CD drive (usually D):
X:\setup.exe
Press <Enter>. Typically, this setup program runs automatically when
you insert the CD.
2. Click the Next button at the Welcome screen to start the installation
and accept the license agreement.
Note If you have a previous version of the NI-VXI software installed, Setup installs the
new version over the previous version.
•
Typical setup installs runtime support and NI-VISA development
support.
•
Complete setup installs everything including NI-VXI API
development support. For more information about the NI-VXI
API, refer to Chapter 3, Developing Your Application.
•
Custom setup gives you more control over which driver
components you want installed on your system. This option is
recommended for advanced users.
4. Click the Next button. Confirm that you are ready to install and click
Next again to begin the installation.
5. Setup now copies the necessary files to your hard drive and creates
program icons.
Completing the Software Installation
Review the information in any READMEfiles that Setup prompts you to
read.
When the installation process completes, reboot the system for the changes
to take effect. If you backed up the manufacturer and model name files,
VXI-USB User Manual
2-2
ni.com
Chapter 2
Installation and Configuration
restore them to the TBLsubdirectory of your NI-VXI directory before
running MAX.
Note If you save and restore the TBL files from an older version of NI-VXI, the software
will use TBL files that do not have the latest updates from National Instruments and may
not include recent hardware releases. If you added additional manufacturer or model names
to your TBL files, we recommend merging those changes with the latest updates included
with this version of NI-VXI, so that all your devices are properly identified.
This section contains basic information about configuring your VXI-USB
hardware. Because the default settings for your VXI-USB hardware are
acceptable for most typical applications, this section is optional.
hardware and software default settings.
Use Measurement & Automation Explorer (MAX) to change any
VXI-USB configuration settings. You can also use MAX to check for
software updates, including updates that may be available for the VXI-USB
firmware. Figure 2-1 shows the firmware update panel.
Figure 2-1. VXI-USB Firmware Update Panel
© National Instruments Corporation
2-3
VXI-USB User Manual
Chapter 2
Installation and Configuration
For information about the software, including optional settings, use MAX
and its online help. Use the Windows Start menu to open the program
group for National Instruments, launch MAX, and select Help»Help
Topics.
Installing the Hardware
This section summarizes how to install your VXI-USB hardware. Your kit
Caution To guard against electrostatic discharge, touch the antistatic plastic packages to a
metal part of your computer or chassis before removing the boards from their packages.
Your computer or chassis should be plugged in but powered off.
Figure 2-2 shows a system that includes a USB 2.0-equipped computer, a
VXI-USB, and USB devices.
2
3
1
N
A
T
IN
T
I
S
O
UM
N
A
E
R
L
N
TS
®
5
b
us
4
1
2
3
External Computer
Connections to Other USB Devices
VXI Mainframe
4
5
VXI-USB in Slot 0
USB Cables
Figure 2-2. USB System
VXI-USB User Manual
2-4
ni.com
Chapter 2
Installation and Configuration
Installing Your VXI-USB Interface Module
All kits contain a VXI-USB interface module.
To install the VXI-USB in Slot 0 of your VXI chassis, complete the
following steps:
1. Power off the chassis.
2. Verify that the backplane connector is intact and that there are no bent
or missing pins on the module.
3. Insert the VXI-USB into the chassis in Slot 0, as shown in Figure 2-2.
4. Power on the chassis.
The VXI system controllers operate certain VXI lines as required for VXI
systems. Verify that any other VXI devices with system controller
capability that are in the same chassis are not configured as system
controller.
Caution Having more than one device configured as system controller can damage the
VXI system.
For VXI systems that include VME devices, ensure that the VME devices
are not configured in the upper 16 KB (starting from 0xC000) of the A16
address space. This region is reserved for VXI device configuration
registers, which are used for initializing, configuring, and interacting with
VXI devices. The VXI-USB also uses this region for this purpose.
This is the VXI-USB logical address, which you cannot change.
Connecting Cables
Connect the USB cable to a USB connection in your host PC and to the
VXI-USB, as shown in Figure 2-2. You can use any available USB port on
the PC for each device. The VXI-USB has two external ports for devices.
You can connect any other USB devices to any available port on a
VXI-USB, but for best performance, minimize the number of USB
devices/hubs in the system. Adding to the number of devices in the tree
degrades system performance.
faster when connected to a Hi-Speed USB port as described in the USB 2.0 specification.
USB 2.0 ports are often integrated on the motherboard of current computers. National
Instruments recommends using an integrated USB 2.0 port, if available, for optimal
© National Instruments Corporation
2-5
VXI-USB User Manual
Chapter 2
Installation and Configuration
performance. Plug-in boards with USB 2.0 ports are also supported but may not provide
the highest performance. Full-speed (USB 1.x) ports are supported as well, but provide
much lower performance. The LINK light (refer to Chapter 1, Introduction) on the front
panel of your VXI-USB controller indicates your connection speed.
Software Configuration and Verification
To configure the software and verify the configuration, follow these steps:
1. Run MAX. You must run the Resource Manager (Resman) every time
the chassis or computer power is cycled, so that your application can
access devices in the VXI chassis. You can also configure MAX to run
Resman automatically at every computer startup by selecting
Tools»NI-VXI»VXI Options and selecting the appropriate checkbox.
Instruments hardware in your system. Use the right-click help for
information about the various configuration options. After you finish
configuring the system through MAX, verify the configuration
through the interactive control utility, VISAIC (Start»Programs»
National Instruments»VISA»VISA Interactive Control), as
described in Chapter 3, Developing Your Application.
Note If you are using extenders such as MXI-2 to create a multichassis system, you may
need to run Resman before configuring some of your devices. Also, if you are using
multiple VXI-USB controllers to create a multisystem configuration, you configure each
system separately.
VXI-USB User Manual
2-6
ni.com
3
Developing Your Application
This chapter discusses the software utilities you can use to start developing
applications that use NI-VXI.
After installing the NI-VXI software, you can begin developing your
VXI/VME application. Be sure to check the release notes for the latest
application development notes and changes.
NI-VXI, NI-VISA, and Related Terms
Before you develop your application, it is important to understand the
difference between NI-VXI, NI-VISA, and similar terms.
•
NI-VXI is the software package that ships with National Instruments
VXI and VME controllers. NI-VXI includes Measurement &
Automation Explorer (MAX), NI-VISA, NI Spy, Resource Manager
(Resman), VXI device drivers, and other utilities for configuring and
controlling your VXI or VME system.
•
NI-VISA is the native API for communicating with VXI/VME devices.
NI-VISA is the National Instruments implementation of the VISA I/O
standard, which is a common interface to many types of instruments
(such as VXI, GPIB, PXI, Serial, TCP/IP, and so on). NI-VXI is
optimized for use through NI-VISA, and NI recommends using
NI-VISA to develop all new VXI/VME applications.
•
The NI-VXI API is an optional development environment that is not
part of the default NI-VXI installation. The NI-VXI API was
developed before NI-VISA; although NI-VXI still supports the
NI-VXI API, NI recommends using NI-VISA for all new VXI/VME
applications. If you must develop an application using the older
NI-VXI API, run the NI-VXI installer and perform a Complete install,
or select the appropriate option in the custom installation screen. Be
sure to review the NI-VXI API Notes section.
•
The NI-VXI compatibility layer allows older programs that use the
NI-VXI API to communicate with VXI devices through VISA. Using
this compatibility layer, older programs can run in NI-VXI 3.0 or later
without being rewritten to use the VISA interface. This layer installs
with NI-VXI by default. It should be completely transparent and
© National Instruments Corporation
3-1
VXI-USB User Manual
Chapter 3
Developing Your Application
provide a high level of performance; however, there may be some
slight changes in behavior for certain applications.
Your software features several system development utilities including
MAX, Resman, NI Spy, VISA Interactive Control (VISAIC), and
optionally VXI Interactive Control (VIC). You can also access online help
and a variety of examples to learn how to use NI-VXI for certain tasks.
Each component assists you with one of four development steps:
configuration, device interaction, programming, and debugging.
You can access the utilities, help files, and release notes through the
Windows Start menu by opening the National Instruments»VXI or
National Instruments»VISA program groups.
Configuration
The configuration utilities in your software kit are Resman and MAX.
Resman performs VXI Resource Manager functions as described in the
VXIbus specification. Resman configures all devices on the VXI backplane
for operation and allocates memory for devices that request it. Resman does
not require you to specify any settings; it automatically performs the VXI
resource management whenever you run it.
Note Power cycling resets all devices, so you must run Resman to reconfigure your
system every time you cycle the power on the chassis.
MAX presents a graphical display of your entire test and measurement
system to help you configure various components. When you launch MAX,
you see all your devices (including VXI) on the screen. You can view the
properties (such as logical address, address space, and so on) of each device
by clicking the device in the configuration tree. To see additional
configuration options for a given device, right-click the device in the
configuration tree. When you access the properties of most National
settings by selecting Hardware Configuration.
MAX and Resman are designed to work together. You can run Resman
through MAX by either clicking the Run VXI Resource Manager button in
the toolbar or right-clicking a specific VXI system on which to run Resman,
as shown in Figure 3-1. You can also select Tools»NI-VXI»VXI Resource
Manager to run Resman on all VXI systems. From the VXI Options dialog
box in the Tools»NI-VXI menu, you can also use MAX to configure
Resman to run on all VXI systems automatically when the computer boots.
VXI-USB User Manual
3-2
ni.com
Chapter 3
Developing Your Application
Resman reports to MAX all errors it finds in your system. When you view
your VXI system in MAX, you can easily spot any errors that Resman
found while configuring the system.
Figure 3-1. Right-Click a VXI System in MAX to Run Resman on that System
After Resman detects and configures all your VXI/VME devices, you can
use MAX to view specific information about each device in your system.
The default MAX view of a VXI system shows the General tab window,
which contains a summary of key information about each device, including
its device name, logical address, model name, and other data. For more
information about MAX, refer to its online help by selecting the
Help»Help Topics menu.
Device Interaction
You can interact with your VXI/VME devices using the VISA Interactive
Control (VISAIC) utility. VISAIC allows you to control your VXI/VME
devices without using LabVIEW, Measurement Studio, LabWindows/CVI,
or another programming language. You can also control your devices in
MAX by right-clicking a device name and selecting Open VISA Session.
devices and develop and debug VXI application programs. VIC is not included in the
default NI-VXI installation. To install VIC, choose either a Complete install or select
NI-VXI API Development from the custom installation screen in the installer. You can
© National Instruments Corporation
3-3
VXI-USB User Manual
Chapter 3
Developing Your Application
subgroups in Start»Programs»National Instruments.
Try the following in VISAIC: In the tree view, navigate using your mouse
to the VISA resource for your controller—probably VXI0::0::INSTR,
representing the VXI system 0, logical address 0 instrument resource, as
shown in Figure 3-2.
Figure 3-2. Select Your Controller in VISAIC
Open the selected resource and navigate to the Register I/O tab. In this tab,
you can read registers on your device, such as the VXI device configuration
registers. Execute the viIn operation (called In in LabVIEW compatibility
mode) with the default parameters. The Data Value field shows the I/O
operation result, such as 0x9ff6. The Return Value field shows the
function status, such as 0 for VI_SUCCESS, as shown in Figure 3-3.
VXI-USB User Manual
3-4
ni.com
Chapter 3
Developing Your Application
Figure 3-3. Successful viIn Access in the VISAIC Register I/O Tab (This Window May
Look Slightly Different for LabVIEW Users)
If the data value ends in FF6, you have successfully read the National
Instruments manufacturer ID from your VXI/VME controller’s ID register.
You may now want to read the configuration registers from other VXI
devices in your system by opening the devices in VISAIC. Try reading a
register from each device listed in the MAX view of your VXI system. This
way, you can verify that your VXI controller can access each device in your
VXI system successfully. You can also access VXI and VME devices
configured in A16, A24, or A32 space by opening the VXI MEMACC
resource, which is VISA’s representation of VXI memory. For more
information about VISAIC operations and commands, refer to the online
help in the Help menu and the context-sensitive help (such as What’s
This?), available by right-clicking in any panel.
Programming for VXI
NI-VISA and the NI-VXI API are the two National Instruments
programming interfaces for accessing your VXI/VME instruments. With
NI-VXI 3.0 or later, NI-VISA is the native API for communicating with a
VXI or VME system, and NI recommends using it for all new applications.
© National Instruments Corporation
3-5
VXI-USB User Manual
Chapter 3
Developing Your Application
Older programs that use the NI-VXI API now use the NI-VXI-to-NI-VISA
compatibility layer to communicate with the VXI devices. Using this layer,
use the VISA interface.
Note The NI-VXI API development environment is not installed by default as part of the
NI-VXI installation. If you must develop an application using the older NI-VXI API, run
the NI-VXI installer and perform a Complete install or select the appropriate option in the
custom installation screen. Be sure to review the NI-VXI API Notes section.
NI-VISA is the National Instruments implementation of the VISA API as
the VXIplug&play standard defines. It provides a common interface to
many types of instruments (such as VXI, GPIB, PXI, Serial, TCP/IP, and
so on) and therefore is especially useful in situations where you are using
multiple types of instruments.
Both NI-VISA and the NI-VXI API include functions for register-level
access to VXI instruments and messaging capability to message-based
devices. You can also use either interface to service asynchronous events
such as triggers, signals, and interrupts, and also assert them. Compatibility
with the NI-VXI API is included for legacy applications only—
NI recommends that you write all new VXI/VME applications in VISA.
The best way to learn NI-VISA programming is by reviewing the example
programs your software includes. The examples directory contains working
VISA programs that illustrate many different types of applications. You can
find these examples in the VXIpnp\WinNT\NIvisa\Examplesdirectory.
high-level calls and send messages with word-serial functions. The
NI-VISA examples for these tasks are HighReg.cand RdWrt.c. Refer to
the other examples as you try more advanced techniques. Consult the
NI-VISA online help for additional information about these topics.
Table 3-1 summarizes the topics the example programs address. All files
are in the VXIpnp\WinNT\NIvisa\Examplesdirectory, in the
subdirectories listed below.
VXI-USB User Manual
3-6
ni.com
Chapter 3
Developing Your Application
Table 3-1. NI-VISA/NI-VXI Examples
NI-VXIExample
(Optional)
Coverage
NI-VISA Example
Message-Based
Access
General\RdWrt.c
VXIws.c
High-Level
Register Access
VXI-VME\HighReg.c
VXIhigh.c
VXIlow.c
VXIint.c
VXItrig.c
Low-Level Register VXI-VME\LowReg.c
Access
Interrupt Handling VXI-VME\AsyncIntr.c
and WaitIntr.c
Trigger Handling
VXI-VME\WaitTrig.c
Note MAX includes configuration options that affect low-level functions and shared
memory, as well as trigger mappings and other attributes of your VXI system. Refer to the
MAX online help for information regarding these options.
Optimizing Large VXIbus Transfers
For best performance, keep the following in mind when using viMove()
or VXImove():
•
•
•
Make sure your buffers are 32-bit aligned.
Transfer 32-bit data whenever possible.
Use VXI block access privileges to significantly improve performance
to devices that can accept block transfers, and likewise use D64 access
privileges for devices that can accept the VME64 64-bit data transfer
protocol.
•
•
To optimize move performance on virtual memory systems such as the
Windows operating system, lock the user buffer in memory yourself so
the move operation does not need to lock the buffer.
To optimize move performance on paged memory systems such as the
Windows operating system, use a contiguous buffer so the move
operation does not need to build a scatter-gather list for the user buffer.
Note viMemAlloc()or VXImemAlloc()returns 32-bit aligned, page-locked,
continuous buffers that work efficiently with the move operations.
© National Instruments Corporation
3-7
VXI-USB User Manual
Chapter 3
Developing Your Application
NI-VXI API Notes
The following notes apply only if you are using the NI-VXI API. We
recommend that all new VXI/VME applications use the NI-VISA API, but
you can still develop with the older NI-VXI API for compatibility with
legacy code.
Compiler Symbols
You may need to define certain compiler symbols so that the NI-VXI
library can work properly with your program. The required symbol
indicates your operating system platform; for example, VXINT designates
the application as a Windows 2000/NT/XP/Me/98 application.
Note LabWindows/CVI automatically defines the correct symbol. You do not need to
define VXINTwhen using LabWindows/CVI.
The additional symbol BINARY_COMPATIBLEis optional. It ensures that
the resulting application is binary compatible with other National
Instruments VXI controllers using the same operating system. This symbol
may cause a slight performance degradation when you use low-level
VXIbus access functions on some controllers.
You can define these symbols using #definestatements in your source
code or using the appropriate option in your compiler (typically either –D
or /D). If you use #definestatements, they must appear in your code
before the line that includes the NI-VXI API header nivxi.h.
Compatibility Layer Options
Although NI-VXI supports multiple VXI controllers through NI-VISA, the
NI-VXI API supports only a single controller. To specify which controller
the emulation layer should use, run MAX. Select Tools»NI-VXI»VXI
Options. Select the VXI system that will support the emulation layer.
In NI-VXI 3.0 or later, when you enable for triggers or interrupts, only the
local controller is enabled. In the NI-VXI API functions for enabling
triggers and interrupts, the controller parameter is ignored. If you need to
enable a remote controller for triggers, use the MAX frame resource to map
the trigger back to the local controller.
The interrupt and trigger routing in the NI-VXI 3.0 or later low-level
drivers is somewhat different from the default routing in previous versions
of NI-VXI. Therefore, the compatibility layer may behave differently than
the original NI-VXI API with regard to these settings. In particular, if you
VXI-USB User Manual
3-8
ni.com
Chapter 3
Developing Your Application
are receiving triggers on an external controller, you may need to modify the
trigger configuration on your extender module using MAX. In general,
interrupts are routed automatically based on the interrupt configuration the
resource manager detects. Whether the changed routing behavior affects
your program is application dependent.
Because VISA is an instrument-centric API, certain functions from the
more controller-centric NI-VXI API do not match perfectly with a VISA
counterpart. When an application enables an event with the NI-VXI API
compatibility layer, each logical address is enabled for that event
separately. For example, if the application enables an interrupt level, VISA
will enable the interrupt on each logical address, one at a time, until all the
devices are enabled. This means that some interrupts could be lost from
devices with higher numbered logical addresses. MAX provides an
option for users to pick which logical address is enabled first. Select
Tools»NI-VXI»VXI Options. Set Prioritized Signal LA to the logical
address of the device that generates the events. This prevents possible loss
of events from that device.
Debugging
NI Spy and VISAIC are useful utilities for identifying the causes of
problems in your application.
NI Spy tracks the calls your application makes to National Instruments
highlights functions that return errors, so during development you can
quickly spot which functions failed during a program’s execution. NI Spy
can log the calls your program makes to these drivers so you can check
them for errors at your convenience, or use the NI Spy log as a reference
when discussing the problem with National Instruments technical support.
Figure 3-4 shows an example of an error returned from a call to
viMemAlloc.
© National Instruments Corporation
3-9
VXI-USB User Manual
A
Specifications
This appendix lists the specifications for the VXI-USB module.
Requirements
Environmental
VXIbus configuration space................... 64 B
Default.................................................... None
Maximum altitude.................................. 2,000 m
Pollution Degree .................................... 2
Indoor use only
Operating Environment
Ambient temperature range.................... 0 to 55 °C (Tested in accordance
with IEC-60068-2-1 and
IEC-60068-2-2.)
Relative humidity range......................... 10% to 90% (Tested in
accordance with
IEC-60068-2-56.)
Storage Environment
Ambient temperature range.................... –20 to 70 °C (Tested in
accordance with IEC-60068-2-1
and IEC-60068-2-2.)
Relative humidity range......................... 5% to 95% (Tested in accordance
with IEC-60068-2-56.)
EMI ........................................................ FCC Class A verified, EC verified
© National Instruments Corporation
A-1
VXI-USB User Manual
Appendix A
Specifications
Shock and Vibration
Operational shock...................................30 g peak, half-sine, 11 ms pulse
(Tested in accordance with
IEC-60068-2-27. Test profile
developed in accordance with
MIL-PRF-28800F.)
Random vibration
Operating.........................................5 to 500 Hz, 0.3 grms
Nonoperating...................................5 to 500 Hz, 2.4 grms
(Tested in accordance with
IEC-60068-2-64. Nonoperating
test profile exceeds the
requirements of
MIL-PRF-28800F, Class 3.)
Power Requirement
+5 V (excluding downstream USB devices)
Typical.............................................2 A
Maximum ........................................4 A
–5.2 V
Typical.............................................200 mA
Maximum ........................................500 mA
–2 V
Typical.............................................100 mA
Maximum ........................................250 mA
Physical
Size .........................................................C size, C-1
Dimensions ............................................. 23.3 × 43.0 cm (9.2 × 13.4 in.)
Weight ....................................................1.14 kg (2.5 lb)
I/O connectors
USB device (Series A).....................2
USB host (Series B).........................1
SMB.................................................3
VXI-USB User Manual
A-2
ni.com
Appendix A
Specifications
Slot requirements ................................... Single VXI C-size slot
Compatibility ......................................... Fully compatible with VXI
specification
VXI keying class.................................... Class 1 TTL
MTBF..................................................... Contact factory
USB Capability Description
USB 2.0, backward compatible with USB 1.1 host and devices.
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
•
•
•
IEC 61010-1, EN 61010-1
UL 61010-1
CAN/CSA-C22.2 No. 61010-1
Note For UL and other safety certifications, refer to the product label or visit
ni.com/certification, search by model number or product line, and click the
appropriate link in the Certification column.
Electromagnetic Compatibility
Emissions ............................................... EN 55011 Class A at 10 m
FCC Part 15A above 1 GHz
Immunity................................................ EN 61326:1997 + A2:2001,
Table 1
CE, C-Tick, and FCC Part 15 (Class A) Compliant
Note For EMC compliance, operate this device with shielded cabling.
© National Instruments Corporation
A-3
VXI-USB User Manual
Appendix A
Specifications
CE Compliance
This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:
Low-Voltage Directive (safety)..............73/23/EEC
Electromagnetic Compatibility
Directive (EMC).....................................89/336/EEC
Note Refer to the Declaration of Conformity (DoC) for this product for any additional
regulatory compliance information. To obtain the DoC for this product, visit
ni.com/certification, search by model number or product line, and click the
appropriate link in the Certification column.
Cleaning
If you need to clean the module, use a soft, nonmetallic brush. Make sure
that the module is completely dry and free from contaminants before
returning it to service.
VMEbus Capability Codes
A64, A32, A24, A16 (master)
VMEbus master A64, A32, A24, and A16 addressing
A16 (slave)
VMEbus slave A16 addressing
D64, D32, D16, D08(EO) (master)
VMEbus master D64, D32, D16, and D08 data sizes
D16, D08(EO) (slave)
VMEbus slave D16 and D08 data sizes
BLT, MBLT (master)
VMEbus master block and D64 transfers
RMW (master)
VMEbus master read/modify/write transfers
RMW (slave)
VMEbus slave read/modify/write transfers
VXI-USB User Manual
A-4
ni.com
Appendix A
Specifications
RETRY (master)
VMEbus master retry support
RETRY (slave)
VMEbus slave retry support
FSD
First slot detector
SCON
VMEbus System Controller (Automatic Detection)
PRI, RRS
Prioritized or Round Robin Select arbiter
ROR, FAIR
Release on Request and FAIR bus requester
IH(7-1)
Interrupt handler for levels 7–1
I(7-1)
Interrupt requester for levels 7–1
D32, D16, D08(O) (Interrupt Handler)
VMEbus D32, D16, D08(O) interrupt handler
D32, D16, D08(O) (Interrupter)
VMEbus D32, D16, D08(O) interrupter
ROAK, RORA
Release on Acknowledge or Register Access interrupter
BTO(x)
VMEbus bus timer (programmable limit)
LOCK
Can lock the VMEbus for indivisible transfers
© National Instruments Corporation
A-5
VXI-USB User Manual
B
Default Settings
This appendix summarizes the default settings for the hardware and
software in the VXI-USB kit. If you need more information about a
particular setting or want to try a different configuration, refer to
Appendix C, Advanced Hardware Configuration Settings, for your
reference.
Default Hardware Settings
Figure B-1 and Table B-1 show the factory-default settings of the
user-configurable switches on the VXI-USB.
© National Instruments Corporation
B-1
VXI-USB User Manual
Appendix B
Default Settings
Table B-1. VXI-USB Hardware Default Settings
Hardware Component
Default Setting
S1—Firmware recovery
N: do not recover firmware
From onboard oscillator
ON: terminated
S2—VXIbus CLK10 source
S3—SMB trigger in termination
S4—SMB CLK10 in termination
S5—SMB CLK10 direction
S6—SMB CLK10 out polarity
ON: terminated
IN: receive CLK10 signal
Noninverted
Default Software Settings
Table B-2. MAX USB Tab Default Settings
Editor Field
USB block size
Default Setting
64 KB
Table B-3. MAX VXI Bus Tab Default Settings
Editor Field Default Setting
Bus timeout value
500 µs
VXI retry generation
Automatic retries
A24/A32 write posting
Transfer limit (bytes)
Requester mode
Enabled
Disabled
Disabled
256/2048 for 2eVME protocol
Release on Request
3
Request level
Fair requester
Enabled
Bus arbitration mode
Arbiter timeout
Prioritized
Enabled
© National Instruments Corporation
B-3
VXI-USB User Manual
C
Advanced Hardware
Configuration Settings
This appendix describes the alternate hardware configuration settings of the
VXI-USB. The board is set at the factory for the most commonly used
configuration. Use this appendix if you want to try a different hardware
configuration or if you would like more information on a particular setting.
This information is intended for more advanced users.
The following hardware configuration settings are user configurable.
•
•
•
Firmware recovery
VXIbus CLK10 routing
Trigger input termination
For the configuration switch locations and default settings, see Figure B-1,
VXI-USB Hardware Default Settings.
Note Do not attempt an alternate setting unless you are familiar with its purpose.
In addition, do not reconfigure any switches or jumpers not described in this appendix
unless directed by National Instruments support.
Firmware Recovery
The VXI-USB has an onboard EEPROM and flash memory that stores
default hardware behaviors loaded at power-on.
The Firmware Recovery Setting switch (S1) causes the VXI-USB to boot
from the firmware image stored on the host. This is useful in the event that
the onboard firmware memory becomes corrupted in such a way that the
VXI-USB boots to an unusable state.
Figure C-1 shows the configuration settings for firmware recovery
operation.
© National Instruments Corporation
C-1
VXI-USB User Manual
Appendix C
Advanced Hardware Configuration Settings
Y
N
Y
N
S1
S1
A. Boot from Onboard EEPROM
and Flash Memory (Default)
B. Boot from Firmware
Image Stored on Host
Figure C-1. Firmware Recovery Operation
VXIbus CLK10 Routing
The VXI-USB has four hardware switches that work together to control
various aspects of CLK10 routing. Read this section carefully and notice
that if you change one switch, you may need to change another. This section
includes several diagrams that show how to configure the four switches to
accomplish various CLK10 configurations.
Notice that the configuration of one switch may make the setting of another
switch irrelevant. The drawings use the
pattern to depict switches that
are either irrelevant or disabled for a particular CLK10 configuration.
Switch S3 uses this pattern in all of the CLK10 drawings. It deals with the
external trigger input SMB and is discussed later in this appendix.
The VXI-USB can use two different sources to generate the VXIbus
CLK10 signal—an onboard oscillator or the external CLK SMB connector.
Use switch S2 to select between these options. The VXI-USB uses the
onboard oscillator by default.
The VXI-USB can also be configured to drive the external CLK SMB from
the VXIbus CLK10 signal. Switch S5 controls whether the VXI-USB
drives or receives the external CLK SMB. If you change the S5 setting to
drive CLK10 out the external CLK10 SMB connector, do not set switch S2
to receive the SMB CLK10 signal. Instead, use its default setting so that the
onboard oscillator generates the signal.
You can use an additional switch, S6, to control the polarity of the external
CLK SMB signal when S5 is configured to drive it. S6 is unused when S5
is configured to receive the external CLK SMB signal.
VXI-USB User Manual
C-2
ni.com
Appendix C
Advanced Hardware Configuration Settings
When switch S5 is set so that the VXI-USB receives the SMB CLK10
signal, you have the option to add a 50 Ω termination to the signal by setting
switch S4. S4 is unused when S5 is configured to drive the external CLK
SMB signal.
Table C-1 summarizes the most common configuration types.
Table C-1. Common CLK10 Routing Configurations
Switches
S2 CLK10
Source
S4
S5
Direction
S6
Polarity
Description
Terminate
Generate internal CLK10 with
onboard oscillator
ONBRD
ONBRD
ONBRD
SMB
N/A
N/A
N/A
N
IN
OUT
OUT
IN
N/A
NON
INV
N/A
N/A
Generate internal CLK10 and drive
to external CLK SMB
Generate internal CLK10 and drive
inverted to external CLK SMB
Receive external CLK SMB and
drive to the backplane unterminated
Receive external CLK SMB with
50 Ω termination and drive to the
backplane
SMB
Y
IN
Figure C-2 shows the default settings for the CLK10 switches. This
configuration is as follows:
•
•
•
•
CLK10 is generated from the onboard oscillator (S2).
The CLK10 signal is terminated (S4).
The VXI-USB receives the external CLK10 signal (S5).
The polarity of the CLK10 signal (S6) is irrelevant when the VXI-USB
receives the external CLK10 signal. However, it is configured to be
noninverted when the CLK10 SMB is used as output.
© National Instruments Corporation
C-3
VXI-USB User Manual
Appendix C
Advanced Hardware Configuration Settings
From
Onboard
Oscillator
From SMB
CLK10 In
S1
S2
Inverted
ON
OUT
Noninverted
IN
S3
S4
S5
S6
Figure C-2. Default Settings for CLK10 Switches
In Figures C-3 and C-4, switch S2 uses the alternate configuration to
generate the VXIbus CLK10 signal. Instead of the onboard oscillator, the
VXI-USB generates from the external CLK SMB connector and drives to
the backplane. You can choose whether to terminate the signal using S4.
Polarity remains irrelevant to these configurations.
From
Onboard
Oscillator
From SMB
CLK10 In
S1
S2
ON
OUT
IN
OFF
S3
S4
S5
S6
VXI-USB User Manual
C-4
ni.com
Appendix C
Advanced Hardware Configuration Settings
From
Onboard
Oscillator
From SMB
CLK10 In
S1
S2
ON
OUT
OFF
IN
S3
S4
S5
S6
Figure C-4. Receive External CLK SMB with 50 Ω Termination
and Drive to the Backplane
Figures C-5 and C-6 show two configurations for driving the external CLK
SMB from the VXIbus CLK10 signal by changing switch S5 to its alternate
setting. Switch S2 must be in its default position for these configurations.
Signal termination is not an issue when driving the signal, so the position
of S4 does not matter. The difference between these two configurations is
whether to use inverted or noninverted polarity when driving the signal.
From
Onboard
Oscillator
From SMB
CLK10 In
S1
S2
Inverted
OUT
IN
Noninverted
S3
S4
S5
S6
Figure C-5. Drive Inverted External CLK SMB
© National Instruments Corporation
C-5
VXI-USB User Manual
Appendix C
Advanced Hardware Configuration Settings
From
Onboard
Oscillator
From SMB
CLK10 In
S1
S2
Inverted
OUT
IN
Noninverted
S3
S4
S5
S6
Figure C-6. Drive Noninverted External CLK SMB
Trigger Input Termination
Located within the group of CLK10 switches is switch S3, which controls
whether to put a 50 Ω termination on the external trigger input SMB.
Figure C-7 shows the setting for a nonterminated trigger input SMB. Use
the default setting of Figure C-7B to terminate the trigger input SMB.
S1
S1
S2
S2
ON
ON
OFF
OFF
S3
S4
S5
S6
S3
S4
S5
S6
B. Terminate Trigger
Input (Default)
Trigger Input
Figure C-7. SMB Trigger Input Termination
VXI-USB User Manual
C-6
ni.com
D
Common Questions
This appendix addresses common questions you may have about using the
NI-VISA/NI-VXI software on the VXI-USB platform.
What does hot plugging mean in terms of USB?
The concept of hot plugging in USB means that you can remove and insert
USB cables without powering down your computer and devices. The USB
Plug and Play architecture is designed so that the host computer can
recognize when to load and remove the appropriate drivers.
Does it matter if I plug my VXI-USB or other USB device into any
particular USB port? For example, does it matter whether I plug a
USB device into the USB ports in my computer or into the VXI-USB in
my mainframe?
A USB device may be plugged into any port on the VXI-USB or your
computer. Doing so can change the topology of the system, which may
affect system performance in some cases. The effect may vary greatly,
depending on the system and types of devices installed.
Also, if your computer has integrated USB 2.0, you should use one of the
integrated ports rather than a USB 2.0 plug-in card if possible. Integrated
USB 2.0 ports typically offer better performance due to their tight coupling
with your motherboard and chipset. Of course, if you have the choice
between a USB 2.0 port and a USB 1.x port, always use the USB 2.0 port
even if that means you are using a plug-in card instead of an integrated port.
I need more devices than can fit in one chassis. How can I expand my
VXI-USB system?
You can add another VXI-USB to the system, but the additional chassis will
not share the same VXI bus. The recommended strategy is to use a
VXI-MXI-2, which follows the VXI-6 specification for mainframe
extension. This extends full VXI functionality across multiple mainframes,
including a common device address space and interframe triggering,
interrupts, and bus mastering. Place a VXI-MXI-2 in the same frame as the
Slot 0 VXI-USB, and another VXI-MXI-2 in Slot 0 of the next mainframe.
You can then fill up this mainframe with additional devices.
© National Instruments Corporation
D-1
VXI-USB User Manual
Appendix D
Common Questions
How can I determine the serial number and firmware version of the
VXI-USB module?
This information is displayed in the title bar of the Hardware Configuration
window in MAX.
What is Resman?
Resman is the utility that performs the duties of a VXI Resource Manager
as discussed in the VXIbus specification. When you set a National
Instruments controller to Logical Address 0, you will at some point need to
run Resman to configure your VXI instruments. If your controller uses a
different (nonzero) logical address and is a message-based device, you need
to start Resman before running it on the Logical Address 0 computer. The
VXI-USB is always logical address 0.
When do I need to run Resman?
Run Resman whenever you need to configure your VXI instruments (for
example, when you power cycle either the host computer or the chassis).
You do not need to run Resman if you unplug your USB cable from the host
and plug it in again without power cycling either the chassis or the host
computer.
Which NI-VXI utility program must I use to configure the VXI-USB?
Use MAX to configure the VXI-USB. MAX is in the National
Instrumentsprogram group folder, and a shortcut is on your desktop.
How do I handle VME devices?
Although there is no way to automatically detect VME devices in a system,
you can add them easily through the Add Device Wizard in MAX. Through
this procedure, you can reserve resources for each of your VME devices
and configure MAX to show VME devices on the screen with all your other
devices.
Which NI-VXI utility program must I use to perform startup Resource
Manager operations?
Use the Resman program to perform startup Resource Manager operations
in Start»Programs»National Instruments»VXI. Resman uses the
settings configured in MAX. It initializes your VXI/VMEbus system and
makes the information it collects accessible through MAX. You can also
run Resource Manager operations from MAX. Through MAX, you can also
configure Resman to run automatically at startup.
VXI-USB User Manual
D-2
ni.com
Appendix D
Common Questions
What can I do to make sure that my system is up and running?
The fastest method for testing the system is to run Resman. This program
attempts to access memory in the upper A16 address space of each device
in the system. If Resman does not report any problems, the VXI-USB
communication system is operational. To test individual devices, you can
use the VIC or VISAIC program to interactively issue NI-VXI functions or
NI-VISA operations, respectively. You can use viIn()and viOut()with
the NI-VISA API (or VXIin()or VXIinReg()and VXIout()or
VXIoutReg()with the NI-VXI API) to test register-based devices by
programming their registers. If you have any message-based devices, you
can send and receive messages with the viRead()and viWrite()
operations in the NI-VISA API (or WSrd()and WSwrt()functions in the
NI-VXI API). Notice that VXIinReg()and VXIoutReg()are for VXI
devices only, but you can use VXIin()and VXIout()for both VXI and
VME. Finally, if you are using LabVIEW or LabWindows/CVI and you
have instrument drivers for the devices in your chassis, you can use the
interactive features of these programs to quickly test the functionality of the
devices.
What do the LEDs on the front of the VXI-USB mean?
The VXI-USB has the following front panel LEDs:
•
FAILED—Indicates the VXI-USB is asserting SYSFAIL on the bus
due to a controller failure.
•
SYSFAIL—Indicates the VMEbus SYSFAIL line is asserted by the
VXI-USB or another device on the bus.
•
•
VXI—Indicates the VXI-USB is being accessed as a VXI slave.
ONLINE
–
–
Green—Indicates the VXI-USB is configured by Resman.
Amber—Indicates the VXI-USB is not configured by Resman.
•
•
USB—Indicates there is USB traffic to/from the VXI-USB (this
excludes any traffic to all other downstream USB devices).
LINK
–
Green—Indicates the VXI-USB is connected to a USB host and
has a full-speed (USB 1.x, 12 Mbps) connection.
–
Amber—Indicates the VXI-USB is connected to a USB host and
has a high-speed (USB 2.0, 480 Mbps) connection.
When all six LEDs are solid on, the FPGA image is corrupted. Recover the
firmware to repair the board.
© National Instruments Corporation
D-3
VXI-USB User Manual
Appendix D
Common Questions
When all LEDs except the SYSFAIL LED are on, the hardware detected
that the FPGA PLL lost lock, and the board may be in an unstable state.
Power cycle the board to repair it.
In an empty chassis, when both the SYSFAIL and FAIL LEDs are solid on,
the firmware image is corrupted. Recover the firmware to repair the board.
What kind of signal is CLK10 and what kind of signal do I need for an
external CLK10?
CLK10 is a differential ECL signal on the VXIbus backplane. However, the
oscillator for the VXI-USB and the EXT CLK input from the front panel
use TTL. Therefore, supply a TTL-level signal for EXT CLK, and onboard
voltage converters automatically convert the signal to differential ECL.
What is the accuracy of the CLK10 signal?
The CLK10 generated by the VXI-USB is 100 ppm accurate. If you need
a more accurate CLK10 signal, you can use the EXT CLK input at the front
of the VXI-USB.
VXI-USB User Manual
D-4
ni.com
E
Technical Support and
Professional Services
Visit the following sections of the National Instruments Web site at
ni.comfor technical support and professional services:
•
Support—Online technical support resources at ni.com/support
include the following:
–
Self-Help Resources—For answers and solutions, visit the
award-winning National Instruments Web site for software drivers
and updates, a searchable KnowledgeBase, product manuals,
step-by-step troubleshooting wizards, thousands of example
programs, tutorials, application notes, instrument drivers, and
so on.
–
Free Technical Support—All registered users receive free Basic
Service, which includes access to hundreds of Application
Engineers worldwide in the NI Developer Exchange at
ni.com/exchange. National Instruments Application Engineers
make sure every question receives an answer.
For information about other technical support options in your
area, visit ni.com/servicesor contact your local office at
ni.com/contact.
•
•
Training and Certification—Visit ni.com/trainingfor
self-paced training, eLearning virtual classrooms, interactive CDs,
and Certification program information. You also can register for
instructor-led, hands-on courses at locations around the world.
System Integration—If you have time constraints, limited in-house
technical resources, or other project challenges, National Instruments
Alliance Partner members can help. To learn more, call your local
NI office or visit ni.com/alliance.
If you searched ni.comand could not find the answers you need, contact
your local office or NI corporate headquarters. Phone numbers for our
the Worldwide Offices section of ni.com/niglobalto access the branch
office Web sites, which provide up-to-date contact information, support
phone numbers, email addresses, and current events.
© National Instruments Corporation
E-1
VXI-USB User Manual
Glossary
Symbol
Prefix
pico
Value
10–12
10–9
10– 6
10–3
103
p
n
nano
micro
milli
kilo
µ
m
k
M
G
T
mega
giga
106
109
tera
1012
Symbols
°
degrees
ohms
Ω
A
A
amperes
address
Character code that identifies a specific location (or series of locations) in
memory. In VISA, it identifies a resource.
address modifier
address space
One of six signals in the VMEbus specification used by VMEbus masters
to indicate the address space in which a data transfer is to take place.
A set of 2n memory locations differentiated from other such sets in
VXI/VMEbus systems by six addressing lines known as address modifiers.
n is the number of address lines required to uniquely specify a byte location
in a given space. Valid numbers for n are 16, 24, 32, and 64. In VME/VXI,
because there are six address modifiers, there are 64 possible address
spaces.
© National Instruments Corporation
G-1
VXI-USB User Manual
Glossary
ANSI
API
American National Standards Institute
Application Programming Interface—the direct interface that an end user
sees when creating an application.
arbitration
A process in which a potential bus master gains control over a particular
bus.
B
B
Byte—eight related bits of data, an 8-bit binary number. Also used to
denote the amount of memory required to store one byte of data.
backplane
An assembly, typically a printed circuit board, with 96-pin connectors and
signal paths that bus the connector pins. A C-size VXIbus system will have
two sets of bused connectors called J1 and J2. A D-size VXIbus system will
have three sets of bused connectors called J1, J2, and J3.
BERR*
BIOS
bus error signal
Basic Input/Output System. BIOS functions are the fundamental level
of any PC or compatible computer. BIOS functions embody the basic
operations needed for successful use of the computer’s hardware resources.
block-mode transfer
An uninterrupted transfer of data elements in which the master sources only
the first address at the beginning of the cycle. The slave is then responsible
for incrementing the address on subsequent transfers so that the next
element is transferred to or from the proper storage location. A VME data
transfer may have no more than 256 elements.
bus
The group of conductors that interconnect individual circuitry in a
computer. Typically, a bus is the expansion vehicle to which I/O or other
devices are connected. Examples of buses include the ISA bus, PCI bus,
VXI bus, and VME bus.
bus error
bus master
An error that signals failed access to an address. Bus errors occur with
low-level accesses to memory and usually involve hardware with bus
mapping capabilities. For example, nonexistent memory, a nonexistent
register, or an incorrect device access can cause a bus error.
A device that is capable of requesting the Data Transfer Bus (DTB) for the
purpose of accessing a slave device.
VXI-USB User Manual
G-2
ni.com
Glossary
byte order
How bytes are arranged within a word or how words are arranged within
a longword. Motorola ordering stores the most significant byte (MSB) or
word first, followed by the least significant byte (LSB) or word. Intel
ordering stores the LSB or word first, followed by the MSB or word.
C
C
Celsius
CLK10
A 10 MHz, 100 ppm, individually buffered (to each module slot),
differential ECL system clock that is sourced from Slot 0 of a VXIbus
mainframe and distributed to Slots 1 through 12 on P2. It is distributed to
each slot as a single-source, single-destination signal with a matched delay
of under 8 ns.
Commander
A message-based device that is also a bus master and can control one or
more Servants.
configuration registers
A set of registers through which the system can identify a module
device type, model, manufacturer, address space, and memory
requirements. To support automatic system and memory configuration,
the VXI specification requires that all VXIbus devices have a set of such
registers.
D
Data Transfer Bus
DTB; one of four buses on the VMEbus backplane. The DTB is used by a
bus master to transfer binary data between itself and a slave device.
DMA
Direct Memory Access—a method by which data is transferred between
devices and internal memory without intervention of the central processing
unit. DMA is the fastest method of transferring data to/from computer
memory.
DRAM
Dynamic RAM (Random Access Memory)—storage that the computer
must refresh at frequent intervals.
dynamic
configuration
A method of automatically assigning logical addresses to VXIbus devices
at system startup or other configuration times.
© National Instruments Corporation
G-3
VXI-USB User Manual
Glossary
dynamically
configured device
A device that has its logical address assigned by the Resource Manager.
AVXI device initially responds at Logical Address 255 when its MODID
line is asserted. The Resource Manager subsequently assigns it a new
logical address, to which the device responds until powered down.
E
ECL
Emitter-Coupled Logic
EEPROM
Electronically Erasable Programmable Read Only Memory—ROM that
can be erased with an electrical signal and reprogrammed.
embedded controller
An intelligent CPU (controller) interface plugged directly into the VXI
backplane, giving it direct access to the VXIbus. It must have all of its
required VXI interface capabilities built in.
EMC
electromagnetic compliance
EMI
electromagnetic interference
external trigger
A voltage pulse from an external source that triggers an event.
F
fair requester
A VXIbus device that will not arbitrate for the VXIbus after releasing
it until it detects the bus request signal inactive. This ensures that all
requesting devices will be granted use of the bus.
firmware
Software embedded in the VXI-USB, contained on EEPROM and flash
memory that can be updated with a special utility (part of MAX). In
combination with the hardware, the firmware enables the VXI-USB to act
as a translator between USB and VXI protocols.
G
g
(1) grams
2
(2) a measure of acceleration equal to 9.8 m/s
GPIB
gRMS
General Purpose Interface Bus (IEEE 488)
A measure of random vibration. The root mean square of acceleration
levels in a random vibration test profile.
VXI-USB User Manual
G-4
ni.com
Glossary
H
hex
Hexadecimal—the numbering system with base 16, using the digits 0 to 9
and letters A to F.
Hz
hertz; cycles per second
I
I/O
Input/output—the techniques, media, and devices used to achieve
communication between machines and users.
IEC
International Electrotechnical Commission. The IEC publishes
internationally recognized standards. IEC 60068 contains information
on environmental testing procedures and severities.
IEEE
Institute of Electrical and Electronics Engineers
inches
in.
instrument driver
A set of routines designed to control a specific instrument or family of
instruments, and any necessary related files for LabWindows/CVI or
LabVIEW.
interrupt
A means for a device to request service from another device; a computer
signal indicating that the CPU should suspend its current task to service a
designated activity.
interrupt handler
A VMEbus functional module that detects interrupt requests generated by
interrupters and responds to those requests by requesting status and identify
information.
interrupt level
IRQ*
The relative priority at which a device can interrupt.
interrupt signal
K
K
kilo—the prefix for 1,024, or 210, used with B (byte) in quantifying data or
computer memory.
k
kilo—the standard metric prefix for 1,000, or 103, used with units of
measure such as volts, hertz, and meters.
© National Instruments Corporation
G-5
VXI-USB User Manual
Glossary
L
logical address
An 8-bit number that uniquely identifies each VXIbus device in a system.
It defines the A16 register address of a device, and indicates Commander
and Servant relationships.
M
m
meters
M
mega—(1) the standard metric prefix for 1 million or 106, when used with
units of measure such as volts and hertz; (2) the prefix for 1,048,576, or 220,
when used with B (byte) to quantify data or computer memory.
master
A functional part of a VME/VXIbus device that initiates data transfers on
the backplane. A transfer can be either a read or a write.
message-based
device
An intelligent device that implements the defined VXIbus registers and
communication protocols. These devices are able to use Word Serial
Protocol to communicate with one another through communication
registers.
MODID
Module ID lines—used in VXI to geographically locate boards and to
dynamically configure boards.
MTBF
MXI-3
Mean Time Between Failure
A PCI Master/Slave system implementing the PCI-to-PCI Bridge register
set. It couples two physically separate PCI buses with either a copper or
fiber optic data link capable of 1.5 Gbits/s serial data rates.
N
NI-488.2 or
NI-488.2M
The National Instruments industry-standard software for controlling
GPIB instruments.
NI-DAQ
The National Instruments industry-standard software for data acquisition
instruments.
NI-VISA
The National Instruments implementation of the VISA standard; an
interface-independent software that provides a unified programming
interface for VXI, GPIB, and serial instruments.
VXI-USB User Manual
G-6
ni.com
Glossary
NI-VXI
The National Instruments bus interface software for VME/VXIbus
systems.
Non-Slot 0 device
A device configured for installation in any slot in a VXIbus mainframe
other than Slot 0. Installing such a device into Slot 0 can damage the device,
the VXIbus backplane, or both.
P
PCI
Peripheral Component Interconnect. The PCI bus is a high-performance
32-bit or 64-bit bus with multiplexed address and data lines.
R
register-based device
A Servant-only device that supports VXIbus configuration registers.
Register-based devices are typically controlled by message-based devices
via device-dependent register reads and writes.
Resman
The name of the National Instruments Resource Manager in NI-VXI bus
interface software. See Resource Manager.
Resource Manager
A message-based Commander located at Logical Address 0, which
provides configuration management services such as address map
diagnostic management.
retry
An acknowledge by a destination that signifies that the cycle did not
complete and should be repeated.
RMS
Root mean squared. See gRMS.
S
s
seconds
slave
A functional part of a VME/VXIbus device that detects data transfer cycles
initiated by a VMEbus master and responds to the transfers when the
address specifies one of the device’s registers.
© National Instruments Corporation
G-7
VXI-USB User Manual
Glossary
Slot 0 device
A device configured for installation in Slot 0 of a VXIbus mainframe. This
device is unique in the VXIbus system in that it performs the VXI/VMEbus
System Controller functions, including clock sourcing and arbitration for
data transfers across the backplane. Installing such a device into any other
slot can damage the device, the VXIbus backplane, or both.
SMB
Sub Miniature Type B connector that features a snap coupling for fast
connection.
statically configured
device
A device whose logical address cannot be set through software; that is, it is
not dynamically configurable.
SYSFAIL
A VMEbus signal that is used by a device to indicate an internal failure.
A failed device asserts this line. In VXI, a device that fails also clears its
PASSed bit in its Status register.
T
trigger
Either TTL or ECL lines used for intermodule communication.
Transistor-Transistor Logic
TTL
U
USB
Universal Serial Bus—a serial bus for connecting computers to keyboards,
printers, and other peripheral devices.
V
V
volts
VIC
VXI Interactive Control program, a part of the NI-VXI bus interface
software. Used to program VXI devices and develop and debug VXI
application programs.
VISA
Virtual Instrument Software Architecture. This is the general name given
to VISA and its associated architecture.
VISAIC
VITA
VISA Interactive Control program, a part of the NI-VISA software.
Used to program devices and develop and debug application programs.
VMEbus International Trade Association
VXI-USB User Manual
G-8
ni.com
Glossary
VME
Versa Module Eurocard or IEEE 1014
VMEbus System
Controller
A device configured for installation in Slot 0 or a VXIbus mainframe or the
first slot in a VMEbus chassis. This device is unique in the VMEbus system
in that it performs the VMEbus System Controller functions, including
clock sourcing and arbitration for data transfers across the backplane.
Installing such a device into any other slot can damage the device, the
VMEbus/VXIbus backplane, or both.
VXIbus
VMEbus Extensions for Instrumentation
W
W
watts
Word Serial Protocol
The simplest required communication protocol supported by
message-based devices in a VXIbus system. It utilizes the A16
communication registers to transfer data using a simple polling handshake
method.
write posting
A mechanism that signifies that a device will immediately give a successful
acknowledge to a write transfer and place the transfer in a local buffer. The
device can then independently complete the write cycle to the destination.
© National Instruments Corporation
G-9
VXI-USB User Manual
Index
A
advanced configuration options, 1-4
advanced hardware configuration settings, C-1
application development, 3-1
configuration, 3-2
debugging, 3-9
default configuration settings, B-1
default settings
hardware, B-1
debugging, 3-9
software, B-3
device interaction, 3-3
NI-VXI API notes, 3-8
developing applications, 3-1
device interaction, 3-3
device tab default settings (table), B-3
diagnostic tools (NI resources), E-1
documentation
conventions used in manual, vii
NI resources, E-1
C
cables, connecting, 2-5
CE compliance specifications, A-4
cleaning specifications, A-4
CLK10 routing, VXI bus, C-2
CLK10 signal
E
accuracy, D-4
definition, D-4
electromagnetic compatibility
specifications, A-3
examples (NI resources), E-1
CLK10 switches, default settings (figure), C-4
(table), C-3
common questions, D-1
compatibility layer options, 3-8
compiler symbols, 3-8
completing software installation, 2-2
configuration, 2-1, 3-2
firmware recovery configuration, C-1
front panel features, 1-3
advanced options, C-1
firmware recovery, C-1
options, 1-4
VXI-USB default configuration settings
(figure), B-2
connecting cables, 2-5
H
hardware
advanced configuration settings, C-1
configuration, 2-3, 3-2
conventions used in the manual, vii
© National Instruments Corporation
I-1
VXI-USB User Manual
Index
default settings, B-1
description, 1-2
determining revision, D-2
installation, 2-4
NI-VISA, 1-4, 3-1
examples (table), 3-7
installation, 2-1
NI-VXI, 1-4, 3-1
compatibility layer, 3-1
installation, 2-1
help, technical support, E-1
hot plugging, D-1
utility programs
I
using to perform startup Resource
Manager operations, D-2
installation, 2-1
hardware, 2-4
software, 2-1
NI-VXI API, 3-1
instrument drivers (NI resources), E-1
introduction, 1-1
compatibility layer options, 3-8
notes, 3-8
K
KnowledgeBase, E-1
optimizing large VXIbus transfers, 3-7
overview of VXI-USB kit, 1-2
L
LabVIEW, 1-5
LabWindows/CVI, 1-5
LEDs, 1-3, D-3
physical specifications, A-2
power requirement specifications, A-2
programming examples (NI resources), E-1
programming for VXI, 3-5
M
Measurement & Automation Explorer, 1-4
device tab default settings (table), B-3
Register I/O tab, successful viIn access in
Resman, 1-4, D-2
N
National Instruments
application software, 1-4
support and services, E-1
NI Spy, 3-9
running (figure), 3-3
using to ensure system is up and
running, D-3
(figure), 3-10
when to run, D-2
NI support and services, E-1
Resource Manager, 1-4
VXI-USB User Manual
I-2
ni.com
Index
S
V
safety specifications, A-3
selecting controller in VISAIC (figure), 3-4
serial number, determining, D-2
shock and vibration specifications, A-2
software
VISAIC, 3-10
(figure), 3-5
VISAIC (figure), 3-10
VME devices, handling, D-2
VMEbus capability codes, A-4
VXI 3.0 specification support, 1-2
VXI bus tab default settings (table), B-3
VXI, programming for, 3-5
VXIbus transfers, optimizing, 3-7
VXIbus, CLK10 routing, C-2
VXI-USB
configuration, 2-6
installation, 2-1
completing, 2-2
verification, 2-6
software (NI resources), E-1
specifications, A-1
CE compliance, A-4
cleaning, A-4
application development, 3-1
common questions, D-1
configuration, 2-1, 3-2
default configuration settings, B-1
default configuration settings
(figure), B-2
default software settings, B-3
revision, D-2
electromagnetic compatibility, A-3
environmental, A-1
physical, A-2
power requirement, A-2
requirements, A-1
safety, A-3
shock and vibration, A-2
support, technical, E-1
T
ensuring that system is up and
running, D-3
technical support, E-1
expanding system, D-1
front panel features, 1-3
front panel LEDs, 1-3, D-3
getting started, 1-1
training and certification (NI resources), E-1
troubleshooting (NI resources), E-1
U
hardware
configuration, 2-3
default settings (table), B-3
description, 1-2
USB compatibility description, A-3
USB device, plugging into USB ports vs. into
mainframe, D-1
USB system (figure), 2-4
installation, 2-4
user-configurable settings, C-1
installation, 2-1, 2-5
introduction, 1-1
© National Instruments Corporation
I-3
VXI-USB User Manual
Index
kit overview, 1-2
software
installation, 2-1
specifications, A-1
W
Web resources, E-1
VXI-USB User Manual
I-4
ni.com
|
