Stamina Products Treadmill Inmotions User Manual

Owner's  
Manual  
WARNING  
Exercise can present a health  
risk. Consult a physician  
before beginning any exercise  
program with this equipment.  
If you feel faint or dizzy,  
immediately discontinue use  
of this equipment. Serious  
bodily injury can occur if this  
equipment is not assembled  
and used correctly. Serious  
bodily injury can also occur if  
all instructions are not  
followed. Keep others and  
pets away from equipment  
when in use. Always make  
sure all bolts and nuts are  
tightened prior to each use.  
Follow all safety instructions in  
this manual.  
When calling for parts or  
service, please specify the  
following number.  
45-1002  
STAMINA PRODUCTS  
CAUTION:  
MADE IN CHINA  
Weight on this product should not exceed 250 lbs.  
Product May Vary Slightly  
From Pictured.  
This Product is Produced Exclusively by  
2040 N. Alliance, Springfield, MO 65803  
Customer Service Number  
1 (800) 375-7520  
2005, 12  
2005 Stamina Products, Inc.  
 
CALL US FIRST  
THANK YOU FOR PURCHASING THE  
InMotionTM II Treadmill  
To help you get started, we have pre-assembled most of your  
InMotionTM II Treadmill at the factory with the exception  
of those few parts left unassembled for shipping purposes.  
Simply follow the few assembly instructions set forth in this manual.  
Within a few minutes you will be getting your body into shape and on your  
way to achieving a happier and healthier lifestyle.  
Should you have any questions,  
please call our Customer Service Department toll-free number,  
1 (800) 375-7520  
Monday - Friday, 8:00 A.M. - 5:00 P.M., Central Time.  
3
 
BEFORE YOU BEGIN  
Thank you for choosing the InMotionTM II  
Treadmill. We take great pride in producing this  
quality product and hope it will provide many hours  
of quality exercise to make you feel better, look better  
and enjoy life to its fullest.  
Yes, it's a proven fact that a regular exercise  
program can improve your physical and mental  
health. Too often, our busy lifestyles limit our time  
and opportunity to exercise. The InMotionTM II  
Treadmill provides a convenient and simple method  
to begin your assault on getting your body in shape  
and achieving a happier and healthier lifestyle.  
Before reading further, please review the drawing  
below and familiarize yourself with the parts that are  
labeled.  
Although Stamina tries to manufacture its products  
with the finest materials and uses the highest  
standards of manufacturing, occasionally a part that  
does not fit, is the incorrect size, or is otherwise  
inappropriate is found. Even with the highest  
inspection and quality controls in place these things  
will happen occasionally. Please do not return the  
product. For your convenience, Stamina has a  
Customer Service Department with a toll-free  
number. If a part is missing, does not fit, is the  
incorrect size, or is otherwise inappropriate, please  
call 1 (800) 375-7520 (in the U.S.) between 8:00A.M.  
and 5:00 P.M. Central Time, Monday through Friday.  
Our operators will be able to assist you with your  
problem and the parts will be mailed directly to your  
house.  
Read this manual carefully before using the  
InMotionTM II Treadmill.  
Meter  
U-Shaped Handrail  
Spring Pin  
Right Upright  
Left Upright  
Flywheel  
Walking Belt  
Side Molding  
Upright Support  
Moving Wheel  
Adjustment  
Bracket  
Bumper Stand  
Base Frame  
THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY :  
Wrench  
Allen Wrench (4mm)  
4
 
HARDWARE IDENTIFICATION CHAT  
This chart is provided to help identify the hardware used in the assembly process.  
After unpacking the unit, open the hardware bag and make sure that you have the following items:  
3/16"  
1/4"  
5/16"  
3/8"  
1/2"  
INCHES  
0
0
1/2  
1
1/2  
2
1/2  
3
1/2  
4
1/2  
5
1/2  
6
in.  
mm.  
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150  
MILLIMETERS  
length  
6
8
10  
12  
Place washers, the end of bolts or screws on the circles to check for the  
correct size. Use the small scale to check the sizes of bolts and screws.  
length  
NOTICE: The length of all kinds of screws and bolts are not included  
themselves head, except the flat head screws and bolts.  
Part No. and Description  
Qty  
38  
39  
40  
Bolt, Hex Head (M10 x 1.5 x 20mm)  
4
2
2
Bolt, Hex Head (M12 x 1.75 x 70mm)  
Bolt, Button Head (M6 x 1 x 15mm)  
Arc Washer (M6)  
44  
2
47  
48  
Washer (M10)  
Washer (M12)  
4
2
NOTE: 1. Some of the hardware items listed may be attached to other parts.  
2. Bolt length is measured from the bottom of the bolt head to the end of the bolt.  
5
 
ASSEMBLY INSTRUCTIONS  
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all  
packing materials from your area and place them back into the box. Do not dispose of the packing materials  
until assembly is completed. Read each step carefully before beginning. If you are missing a part please  
call our toll-free number for assistance 1 (800) 375-7520 or e-mail us at:  
Sensor Wire  
STEP 1  
NOTE: The LEFT UPRIGHT(2) is the one with the Sensor Wire.  
Attach the LEFT and RIGHT UPRIGHTS(2, 3) to the UPRIGHT SUPPORT(4) with HEX BOLTS  
(M10 x 20mm)(38) and WASHERS(M10)(47).  
STEP 2  
Slide the SPRING(7) onto the SPRING PIN(6). Insert the threaded end of the SPRING PIN(6) through  
the collar on the RIGHT UPRIGHT(3) and screw the BALL KNOB(8) onto the thread end of the SPRING  
PIN(6). Tighten the BALL KNOB(8) as tight as you can by hand.  
6
 
ASSEMBLY INSTRUCTIONS  
STEP 3: Place the BASE FRAME(1) between the LEFT and RIGHT UPRIGHTS(2, 3) and secure  
with HEX BOLTS(M12 x 70mm)(39) and WASHERS(M12)(48). DO NOT TIGHTEN COMPLETELY.  
STEP 4: Secure the U-SHAPED HANDRAIL(5) onto the LEFT and RIGHT UPRIGHTS(2, 3) with  
BUTTON HEAD BOLTS(6mm x 15mm)(40) and ARC WASHERS(M6)(44). Connect the UPPER  
EXTENSION WIRE(28) to the LOWER EXTENSION WIRE(29).  
STEP 5: Go back and tighten HEX BOLTS(M12 x 70mm)(39) in STEP 2. Connect the LOWER  
EXTENSION WIRE(29) located on the LEFT UPRIGHT(2) to the SENSOR WIRE(30). Insert the  
PULL PIN(9) through the RIGHT UPRIGHT(3) and BASE FRAME(1) to lock the BASE FRAME(1) in  
position.  
STEP 6: Install two "AA" batteries into the METER(26), two batteries included. See page 8 for detailed  
battery installation instructions. Slide the METER(26) onto the plate on the U-SHAPED HANDRAIL(5).  
Connect the UPPER EXTENSION WIRE(28) to the METER(26).  
STEP 7: Attach the BUMPER STANDS(22) to the bottom of the BASE FRAME(1).  
NOTE: The BUMPER STANDS(22) may be stored on the end of the BASE FRAME(1) to increase the  
angle of the treadmill and reduce the walking resistance. See page 10 for details on adjusting the walking  
resistance.  
7
 
USING THE ELECTRONIC METER  
POWER ON : Walking Belt movement or push the button.  
Automatic shut off after 4 minutes of inactivity.  
POWER OFF :  
MODE/CLEAR BUTTON:  
Press and release to select functions.  
Press and hold for three seconds to reset all  
functions to zero.  
FUNCTIONS:  
SCAN: Automatically scans TIME, SPEED, DISTANCE, and CALORIES in sequence with a change  
every four seconds. Press and release the button until " " appears on the display and points  
to SCAN.  
TIME:  
SPEED:  
Displays the time, from 1 sec. up to 99:59 minutes.  
Displays the current speed, from zero to 999.9 Mile/Hr.  
Displays the distance, from zero to 99.99 miles.  
DISTANCE:  
CALORIES:  
Displays the calorie consumption, from zero to 999.9 Kcal.  
The calorie readout is an estimate for an average user. It should be used only as a comparison  
between workouts on this unit.  
AA Batteries  
HOW TO INSTALL AND REPLACE BATTERY:  
1. Open the Battery Door on the back of the meter.  
2. The meter operates with two AA batteries, two batteries included.  
Refer to the illustration to install or replace the batteries.  
NOTE:  
1. Do not mix a new battery with an old battery.  
2. Use the same type of battery. Do not mix an alkaline battery with  
another type of battery.  
3. Rechargeable batteries are not recommended.  
8
 
TREADMILL ADJUSTMENTS  
The basic idea behind the manual treadmill is to have the belt running on a treadmill board and between two  
rollers so that the belt will move without much effort. In order for the belt to run smoothly, there are a few  
points that need to be noted.  
BELT ALIGNMENT  
The belt must be in the center of the treadmill to prevent it from rubbing against the flywheels. If the belt  
rubs a flywheel, it will be difficult to keep the belt moving and eventually damage the edge of the belt.  
The treadmill has belt guides welded to the bottom of the treadmill frame that move the belt toward the  
center of the treadmill. However, the rear roller must be properly aligned with the treadmill frame and front  
roller if the belt is to remain centered on the treadmill.  
The bolts in the rear of the treadmill (one on the left and the other on the right) adjust the alignment of the  
rear roller as well as the tension of the belt.  
The belt will run to the side of the loose rear bolt.  
Hint:  
Eyeball the rear roller to make sure both the right side and the left side of the roller are the same  
distance from the back edge of the treadmill. Use the 4mm ALLEN WRENCH to make these  
adjustments. Turn the bolts Clockwise to tighten and Counter-Clockwise to loosen.  
BELT DRIFTING LEFT  
Turn the left screw 1/4 turn CLOCKWISE and the right screw 1/4 turn  
COUNTER-CLOCKWISE, then walk on the treadmill. Repeat if needed.  
BELT DRIFTING RIGHT  
Turn the left screw 1/4 turn COUNTER-CLOCKWISE and the right screw  
1/4 turn CLOCKWISE, then walk on the treadmill. Repeat if needed.  
NOTE:  
When you believe the WALKING BELT is centered, use the treadmill for three (3) minutes to verify the  
WALKING BELT won't drift to one side. If the WALKING BELT continues to drift, the floor may not be level.  
Rotate the treadmill 90 degrees or move the treadmill to another location.  
BELT TENSION  
The belt should be tight and not lying on the treadmill board. If the belt is too loose, the belt will slip on the  
front roller and you will notice a jerky movement when you walk on the treadmill. If the belt is too tight, the  
edges of the belt will begin to curl and more effort will be required to move the belt. Excessive belt tension  
can also damage the bearings in the rollers. The bolts in the rear of the treadmill (one on the left and the  
other on the right) adjust the tension of the belt as well as the alignment of the rear roller.  
BELT TOO LOOSE: Use the 4mm ALLEN WRENCH to tighten the bolts in the rear of the treadmill.  
Tighten both rollers 1/4 turn at a time until the belt stops slipping on the front roller.  
BELT TOO TIGHT: Use the 4mm ALLEN WRENCH to loosen the bolts in the rear of the treadmill.  
Loosen both rollers 1/2 turn at a time until the belt begins to slip on the front roller. Then use the procedure  
above to tighten the belt.  
9
 
TREADMILL ADJUSTMENTS  
WALKING RESISTANCE  
The walking resistance or effort needed to push the treadmill belt can be adjusted by changing the incline  
angle. This treadmill has two adjustment positions.  
Highest Resistance  
The BUMPER STANDS(22) are attached to  
the bottom of the treadmill.  
Lowest Resistance  
Remove (unscrew) the BUMPER STANDS(22)  
from the bottom of the treadmill and store them  
in the end of the treadmill.  
NOTE:  
1. Since this is a new machine, you may need some time to get used to walking on the treadmill and to  
break it in.  
2. If the walking resistance is still too high, check the BELT TENSION.  
3. The belt resistance can be reduced by adding silicone lubricant between the belt and the board. Wipe  
the board under the belt with a cloth and spray or spread silicone lubricant on the board under the belt.  
MAINTENANCE  
The safety and integrity designed into the InMotionTM II Treadmill can only be maintained when the  
InMotionTM II Treadmill is regularly examined for damage and wear. Special attention should be given to  
the following:  
1. Clean the exposed surfaces of the walking belt and the board with an absorbent cloth.  
2. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.  
3. Verify that the Spring Pin is present and functioning properly. Verify that the Ball Knob is securely  
attached to the Spring pin. Repair or replace parts as necessary.  
4. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts. Tighten  
loose nuts and bolts.  
5. Verify that the Warning Label is in place and easy to read. Call Stamina Products immediately  
(1-800-375-7520) for a replacement Warning Label if the Warning Label is missing or damaged.  
6. Worn or damaged components shall be replaced immediately or the InMotionTM II Treadmill removed  
from service until repair is made.  
7. Only Stamina Products supplied components shall be used to maintain/repair the InMotionTM II  
Treadmill.  
8. Keep your InMotionTM II Treadmill clean by wiping with an absorbent cloth after use.  
9. If the WALKING BELT(17) does not move easily, lubricate the BOARD(18) under the WALKING  
BELT(17) with Silicone Lubricant.  
10  
 
STORAGE  
1. To store the InMotionTM II Treadmill simply keep it in a clean dry place.  
2. To avoid damage to the electronics meter, remove the batteries before storing the InMotionTM II Treadmill  
for one year or more.  
3. Follow the following process to fold The InMotionTM II Treadmill as illustrated for easy storage.  
a. Remove the PULL PIN(9) to unlock the BASE FRAME ASSEMBLY(1).  
b. Fold up the BASE FRAME ASSEMBLY(1). Pull out the BALL KNOB(8) on the spring pin and  
release to lock the BASE FRAME ASSEMBLY(1) in upright position.  
CAUTION: Make sure the Base Frame Assembly is locked securely in folded position by the spring pin.  
c. Store the PULL PIN(9) by inserting the PULL PIN(9) back into the hole in the RIGHT UPRIGHT(3).  
Move the InMotionTM II Treadmill with the moving wheels on the UPRIGHT SUPPORT(4). Grasp  
4.  
the U-SHAPED HANDRAIL(6) to move the InMotionTM II Treadmill.  
UNFOLD THE InMotionTM II Treadmill  
a. Remove the PULL PIN(11) from the RIGHT UPRIGHT FRAME(3).  
b. Pull out the BALL KNOB(10) on the spring pin and unfold the BASE FRAME ASSEMBLY(1).  
c. Lock the BASE FRAME ASSEMBLY(1) in position by inserting the PULL PIN(11) through the RIGHT  
UPRIGHT FRAME(3) and BASE FRAME(1).  
11  
 
PRODUCT PARTS DRAWING  
FRONT  
Belt Guides  
BACK  
12  
 
PARTS LIST  
DIAGRAM#  
PART NAME  
QTY  
1
2
3
4
5
6
7
8
Base Frame  
Left Upright  
Right Upright  
Upright Support  
U-Shaped Handrail  
Spring Pin  
Spring  
Ball Knob  
Pull Pin  
Front Roller /w Flywheels  
Front Shaft  
Bearing (6000zz)  
Plastic Washer (M10)  
Rear Roller  
Rear Shaft  
Adjustment Bracket  
Walking Belt  
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
2
1
1
1
1
2
2
2
2
2
1
4
1
1
1
1
6
2
2
2
6
2
4
2
2
2
2
2
2
6
2
4
2
1
1
1
1
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
Board  
Left Side Molding  
Right Side Molding  
Round Cap (38mm)  
Bumper Stand  
Moving Wheel  
Foam Grip  
Long Foam Grip  
Meter  
Grommet Plug  
Upper Extension Wire  
Lower Extension Wire  
Sensor Wire  
Magnet  
Screw Sleeve  
Round Plug (25mm)  
Rectangular Plug (25mm x 50mm)  
Screw, Flat Head (M3.5 x 15mm)  
Screw, Flat Head (M5 x 25mm)  
Bolt, Hex Head (M6 x 1 x 55mm)  
Bolt, Hex Head (M10 x 1.5 x 20mm)  
Bolt, Hex Head (M12 x 1.75 x 70mm)  
Bolt, Button Head (M6 x 1 x 15mm)  
Bolt, Button Head (M6 x 1 x 70mm)  
Bolt, Button Head (M8 x 1.25 x 15mm)  
Nylock Nut (M6 x 1)  
Arc Washer (M6)  
Washer (M6)  
Washer (M8)  
Washer (M10)  
Washer (M12)  
Warning label  
Wrench  
Allen Wrench (4mm)  
Owner's Manual  
13  
 
LIMITED WARRANTY  
MODEL 45-1002  
WARRANTY  
Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship  
under normal use, service and proper operation for a period of 90 days on the parts and one year on the  
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT  
APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,  
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,  
REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED BY STAMINA  
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,  
gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is  
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household  
purposes.  
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and  
a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071, Springfield  
Missouri, USA, 65801-1071 or call us at 1 (800) 375-7520. If the defect is covered under this limited  
warranty, you will be requested to return the product or part to us for free repair or replacement at our option.  
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE  
(1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED.  
NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE  
(1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not  
transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED  
WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE  
EXCLUSIVE REMEDY AVAILABLE TO YOU. In the event that the purchaser makes any claim under this  
limited warranty or any implied warranty, the Warrantor reserves the right to require the product to be returned  
for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of  
the enclosed warranty registration card is not required for warranty coverage, but is merely a way of  
establishing the date and place of purchase.  
Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF  
TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,  
SPECIAL OR INCIDENTALDAMAGESDUE TO BREACH OF THEABOVE WARRANTY ORANY IMPLIED  
WARRANTY.  
This limited warranty is the only written or express warranty given by Stamina Products, Inc. This warranty  
gives you specific legal rights, and you may also have other legal rights which vary from state to state.  
ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED INDURATION TO THE  
DURATION OF THIS WARRANTY.  
The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to  
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any  
such law is found to be applicable, the foregoing disclaimers and limitations of and on implied warranties and  
consequential and incidental damages with respect thereto shall be disregarded and shall be deemed not to  
have been made to the extent necessary to comply with such legal restriction.  
14  
 
FAX/MAIL ORDERING FORM  
Please do not return the product. For your convenience, Stamina has a Customer Service Department with  
a toll-free number. Should a part be missing or a defective part found, please call 1 (800) 375-7520  
(in the U.S.) between 8:00 A.M. and 5:00 P.M. Central Time, Monday through Friday or fill out the fax sheet  
ordering form below and fax it to (417) 889-8064. Our Customer Service Department will be able to assist  
you with your problem and the part will be mailed directly to your house.  
MAIL  
TELEPHONE  
CUSTOMER SERVICE  
Tel: 1 (800) 375-7520  
FAX  
ONLINE  
CUSTOMER SERVICE  
STAMINA PRODUCTS, INC.  
ATTN: Customer Service  
P.O. Box 1071  
CUSTOMER SERVICE  
Fax: (417) 889-8064  
Springfield, MO. 65801-1071  
Detach and Mail or Fax the Form Below  
Stamina Products, Inc.  
P.O. Box 1071  
Springfield, MO 65801-1071  
Mr./Ms:  
Address:  
City:  
Apt. #:  
Zip Code:  
State:  
IMPORTANT: We must have your phone number in order to process the order!  
Work Phone #: (  
Phone #: (  
)
)
Date Purchased:  
Model #:  
Purchased From:  
IMPORTANT : Before filling out the form below make sure you have the right information.  
Refer to the parts list to make sure you're ordering the right parts!  
PART #  
1
DESCRIPTION  
QUANTITY  
1
EXAMPLE:  
Rear Unit Assembly  
 

Sharp Air Conditioner AE X12FR User Manual
Shure Microphone Super 55 User Manual
Stamina Products Fitness Equipment 20 2015 User Manual
Sterling Plumbing Outdoor Shower 61030110 User Manual
Sunbeam Coffee Grinder EM0410 User Manual
Sunbeam Mixer FPSBHS0301 User Manual
Superior Computer Drive SS2000MD4 User Manual
SV Sound Speaker SVS PB2 ISD User Manual
Sylvania Speaker System SHTIB8108 User Manual
Sylvania TV DVD Combo C6520FDE User Manual